24 Slot Cooler Motor Rewinding Data In Hindi|स्लॉट कूलर मोटर वाइंडिंग डाटा इन हिंदी.29/33 Wire Number.

24 Slot Cooler Motor Full Winding Data. 

In India and some Asian countries, this Cooler motor operates at 200 volts. You can install a capacitor of 4 mfd in a cooler motor.

Cooler motors have more bush applied nowadays and bearings of better quality motors are used nowadays, motors with bearings are better than bush motors because the bearings last longer than the bush and do not deteriorate quickly.

There are several precautions that you should take while winding the Cooler motor. First of all, clean the cooler motor properly. After thoroughly cleaning the cooler motor stator, you put the insulation paper in it. You can put 4 numbers in the insulation paper. You should never forget to put a green sheet in the cooler motor. Because water runs in the cooler during the summer season. And the green sheet quickly deteriorates due to running water. Because the green sheet is not plastic and there is a lot of chance that it will deteriorate due to water moisture.

While moving the cooler motor winding, make coils of it for winding. A total of 4 coils will go into it. 4 coils will be of the running winding and 4 coils will be of the starting winding of the cooler motor. Running winding is called bottom winding in most motors and upward winding is often called starting winding.

Cooler Motor Winding.

Cooler motor winding is done in two ways – one is Single speed and the other is Three-speed winding. Total 4 winding comes out in the single speed winding, while in the three-speed winding, the work is 6 wire out FROM MOTOR WINDING.

3 Speed cooler motor winding Life is small compare to single speed cooler motor winding, so we are always recommended to keep single-phase winding.

In single-speed Motor winding, you can put the red-colored wire in the running winding. And you can put the black wire in the starting winding.

3 Speed Cooler Motor Connection.

A total of 6 wires come out in 3-speed winding. The blue wire is a common wire in the cooler motor. The red wire has working speed, the white wire has medium speed, and black wire has high speed, which is the fastest. And after that, there is a 2 wire starting winding.

At the time of Cooler motor winding, you will enter Wire number 29 in its running winding. And you can enter 33 numbers in the starting winding. The cooler motor winding will have a pitch of running winding 1 to 4 and 1 to 6. You will put Coil once in 1 to 4 pitches. And in the winding of the cooler motor, in 1 to 6 pitch, Coils will have to rotate 2 times.

You can take the help of our YouTube channel for easy winding of the cooler motor. By watching this video, you can wind the cooler motor very easily. You can click on the link given below for more information. And if you get a little help in this video and from this post then don’t forget to like our videos and posts.

If your cooler motor is heating up too soon or too much, then either there is the aluminum wire used in its wiring (aluminum being a not so good conductor, heats up easily due to excessive electrical losses, that’s why the copper wire is preferred in high-performance motors) or the bearings are faulty resulting in more friction or this motor is mounted in a way that the moving air isn’t able to take away it’s heated effectively.

कूलर मोटर वाइंडिंग कनेक्शन डायग्राम जहा पर देखें

Connection+Diagram

24 Slot Cooler Motor Rewinding Winding VIDEO Is Here.

 

cooler motor winding

Cooler motor winding data and 24 slots cooler motor winding data are known as 3 speed cooler motor rewinding/winding also known as 24 slots 1440 rpm cooler motor winding, You will find the complete way to do cooler motor winding in this post.

     Cooler motor winding There are two types of stamping of the cooler motor one is 24 slots and the second is 36 slots. There are two types of Cooler motor winding24 slots and 36 slots. In the cooler’s 24 slots motor also delays down to 4 Coils. And a total of 4 coils is inserted in the Cooler motor of 36 slots 1-inch stamping.

 

 

 

24 Slot Cooler Motor Rewinding Winding Data Here

Core length                  1 inch

inner diameter              3 inch

outer diameter              5 inch

 

Slot.   24

watts 370

 

Rpm 1440

 

Capacitor  = 4 MFD

 

4 pole motor winding.

 

capacitor 4 mfd in 220 volts to 240 volts.

 

5 mfd in the down voltage area.

 

VOLTS  =220

 

RPM = 1440

 

Single Phase Supply

 

WINDING WIRE = COPPER